Need help

View previous topic View next topic Go down

Need help

Post by Big Mike226 on Wed Nov 09, 2011 7:31 pm

Got a 2006 ford 500 and every once in awhile the engine will just rev up to about 4500 rpm. Normal driving 1500 -2000 It tends to happen when running air condition or heat . Any idea what it could be?
avatar
Big Mike226
Co-Founder
Co-Founder

Number of posts : 1104
Age : 54
Location : Laurel Maryland
Registration date : 2007-12-08

View user profile

Back to top Go down

Re: Need help

Post by Boss281 on Wed Nov 09, 2011 8:06 pm

idle air controller? Any codes?

_________________

Torch Red 2005 Mustang GT 5-speed
All motor, stock shortblock and heads, aftermarket cams and intake manifold, full exhaust, 361hp/324trq, 11.89 at 115. Weekend Warrior.
Tuxedo Black 2014 Focus ST 6-speed
My daily commuter...
avatar
Boss281
Geek Stangs
Geek Stangs

Number of posts : 1719
Age : 59
Location : New Windsor
Registration date : 2007-12-06

View user profile http://www.cardomain.com/ride/2059455

Back to top Go down

Re: Need help

Post by BobT on Thu Nov 10, 2011 7:13 am

Normally I would say the IAC valve but my moms cars had the exact same problem. Ford replaced the throttle body and it fixed it. Here`s the TSB.

12/16/10

3.0L - RPM FLUCTUATIONS WITH OR WITHOUT DTCS

FORD:
2005-2007 Five Hundred, Freestyle

MERCURY:
2005-2007 Montego

This article supersedes TSBs 06-21-1 and 09-24-12 to consolidate and update the Service Procedure.

ISSUE
Some 2005-2007 Freestyle, Five Hundred and Montego vehicles equipped with the 3.0L engine may exhibit one or more of the following symptoms:
drive-away hesitation, loss of RPM on deceleration, difficulty starting, and/or idle RPM less than desired. Malfunction indicator lamp (MIL) may or may not be illuminated with diagnostic trouble codes (DTCs) P0506, P0505 or P061B. These conditions may also appear after battery disconnect, dead battery condition, or keep alive memory (KAM) reset.

ACTION
Follow the Service Procedure steps to correct the condition.

SERVICE PROCEDURE

1. Retrieve DTC's from the powertrain control module (PCM).

a. If no codes are present but the symptoms exist or P0505, P0506, P061B are present proceed to Step 2.


2. Using IDS monitor IACTRIM and IACKAM2 PIDs. The engine must be at operating temperature of 170 F (77 C).

3. Record and add the two values.

a. If the total value is 0.5 Lb/Min or greater proceed to Step 4.

b. If the total value is less than 0.5 Lb/Min do not continue with this article. Follow normal Workshop Manual (WSM) or Powertrain Controls/Emissions Diagnosis (PC/ED) for normal diagnostics.


4. Remove the throttle body. Refer to WSM, Section 303-04.








5. Using Motorcraft(R) Choke and Linkage Cleaner or equivalent, spray the throttle body plate and bore. Using a small, soft, solvent resistant brush clean the edges of the throttle plate and the mating surface of the throttle bore to remove all sludge build up. Reapply choke and linkage cleaner. (Figures 1-2)

NOTE DO NOT SPRAY CLEANER DIRECTLY INTO THROTTLE PLATE PIVOT SHAFT.

6. Install the throttle body. Refer to WSM 303-04.








7. Using IDS clear codes and reset keep alive memory (KAM).








Parts Block

WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage
IMPORTANT : Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.

OPERATION DESCRIPTION TIME

102405A 2005-2007 Five Hundred, 0.8 Hr.
Freestyle, Montego: Check
DTCs, Monitor PIDS, And
Clean The Throttle Body
Includes Time To Remove
And Install The Throttle
Body (Do Not Use With
Any Other Labor
Operations)

DEALER CODING
CONDITION
BASIC PART NO. CODE
9F991 49
avatar
BobT
COBRA
COBRA

Number of posts : 875
Age : 38
Location : Westminster
Registration date : 2009-05-07

View user profile

Back to top Go down

Re: Need help

Post by Big Mike226 on Thu Nov 10, 2011 1:30 pm

thanks
avatar
Big Mike226
Co-Founder
Co-Founder

Number of posts : 1104
Age : 54
Location : Laurel Maryland
Registration date : 2007-12-08

View user profile

Back to top Go down

Re: Need help

Post by Bethelism on Thu Nov 10, 2011 7:09 pm

Take it back and get a Smart Car.

_________________

Proud driver of Shela - 2005 Satin Silver GT
Member of the Silver Mustang Registry SMR# 0518
June/July SOTM 2011

Ask me about some of my mods....
All the work here is done by a broad!
avatar
Bethelism
Grand Poobet
Grand Poobet

Number of posts : 1724
Age : 37
Location : Proud Fredneckian.
Registration date : 2008-12-30

View user profile http://www.bethelism.blogspot.com

Back to top Go down

Re: Need help

Post by rgoddard on Mon Nov 14, 2011 8:01 am

Just a heads up but my old truck had the same problem. I did the IAC valve and cleaned and replaced a TB. After all that I replaced the MAF sensor it went away. It just a thought
avatar
rgoddard
BOSS
BOSS

Number of posts : 421
Age : 32
Location : Mount Airy, Maryland
Registration date : 2011-08-30

View user profile

Back to top Go down

Re: Need help

Post by Sponsored content


Sponsored content


Back to top Go down

View previous topic View next topic Back to top


 
Permissions in this forum:
You cannot reply to topics in this forum